Research on the Influence of Inflow Conditions on the Aerodynamic Performance of a Tandem Cascade

Document Type : Regular Article

Authors

School of Power and Energy, Northwestern Polytechnical University, Xi’an, Shaanxi, 710072, P. R. China

Abstract

We perform a thorough numerical analysis of the impact of inflow conditions on the aerodynamic performance of a tandem cascade. In particular, we investigate the effects of the incidence angle and the inlet boundary layer (IBL) thickness on the three-dimensional flow field structure and aerodynamic performance. Our results show that the gap flow strength of the tandem cascade decreases with the increase of incidence angle, and it can effectively reduce the mixing of the wakes of the forward blade (FB) and rear blade (RB). In turn, this prevents the passage vortex (PV) in the RB passage from developing along the circumferential direction. The occurrence of IBL does not modify the effects of the incidence angle on the tandem cascade, however, it reduces the load of the RB and the gap flow strength near the endwall. Under all incidence angles, IBL increases the total pressure loss of the tandem cascade, and decreases the static pressure rise (except for an incidence angle equal to -6°). The maximum loss increment is at 2° incidence angle, and the maximum static pressure rise decrement is at 6° incidence angle (Thick-IBL condition) or 7° incidence angle (Thin-IBL condition). Furthermore, we found that the presence of IBL changes the minimum loss condition from 0° (design condition) to -2° incidence angle. Our results thus indicate that in the practical engineering application of the tandem cascade, the reality that IBL degrades the tandem cascade performance in the full incidence angle range should be considered. And the strong endwall secondary flow effect caused by IBL should be considered in the tandem cascade three-dimensional design, so that the tandem cascade two-dimensional performance advantage can be better played.

Keywords

References

AutoGrid5 v8.7, User Manual (2009). Brussels: NUMECA International.##
Bammert, K. and R. Staude (1980). Optimization for rotor blades of tandem design for axial flow compressors. Journal of Engineering for Gas Turbines and Power 102(2), 369-375.##
Cao, Z., W. Guo, C. Song and B. Liu (2021). Flow physics of highly loaded tandem compressor cascade with non-axisymmetric endwall profiling. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy 235(5), 931-943.##
Chen, P., K. Liesner, R. Meyer and W. Qiao (2012). Effect of inflow variations on compressor secondary flow behavior.  XX Polish Fluid Mechanics Conference, Gliwice.##
Chen, P., W. Qiao, K. Liesner and R. Meyer (2014). Location effect of boundary layer suction on compressor hub-corner separation Turbo Expo: Power for Land, Sea, and Air, GT 2014-25043.##
Cheng, H., B. Liu, J. Li and X. Yang (2017). A study of parameter optimization of axial compressor tandem cascade. Journal of Propulsion Technology 38(10), 2224-2234.##
Choi, M., H. T. Chung, S. H. Oh, H. Y. Ko and J. H. Baek (2011). Effects of inlet boundary layer thickness on characteristics of rotating stall in subsonic axial compressor. Transactions of the Japan Society for Aeronautical and Space Sciences 53(182), 267-274.##
Eshraghi, H., M. Boroomand and A. M. Tousi (2016). A developed methodology in design of highly loaded tandem axial flow compressor stage. Journal of Applied Fluid Mechanics 9(1), 83-94.##
Gbadebo, S. A., N. A. Cumpsty and T. P. Hynes (2005). Three-dimensional separations in axial compressors. Journal of Turbomachinery 127(4), 331-339.##
Hertel, C., C. Bode, D. Kožulović and T. Schneider (2014, June). Investigations on aerodynamic loading limits of subsonic compressor tandem cascades: end wall flow. Turbo Expo: Power for Land, Sea, and Air, GT2014-26978.##
Hoeger, M., R. D. Baier, S. Fischer and J. Neudorfer (2011, July). High turning compressor tandem cascade for high subsonic flows, part 1: Aerodynamic design. 47th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, 5601.##
Ju, Y. and C. Zhang (2010, October). Multi-objective optimization design method for tandem compressor cascade at design and off design conditions. Turbo Expo: Power for Land, Sea, and Air, 44021, 785-796.##
Lewin, E., D. Kožulović and U. Stark (2010, October). Experimental and numerical analysis of hub-corner stall in compressor cascades. Turbo Expo: Power for Land, Sea, and Air, 44021, 289-299.##
Li, Z., X. Zheng, Y. Liu, Q. Li and B. Ji (2016). The effect of end wall boundary layer on matching and corresponding flow control technique for multistage axial compressor. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering 230(12), 2179-2194.##
Liesner, K., R. Meyer, M. Lemke, C. Gmelin and F. Thiele (2010, October). On the efficiency of secondary flow suction in a compressor cascade. Turbo Expo: Power for Land, Sea, and Air, 44021, 151-160.##
Liu, B., C. Zhang, G. An, D. Fu and X. Yu (2021). Using tandem blades to break loading limit of highly loaded axial compressors. Chinese Journal of Aeronautics 35(4), 165-175.##
Mao, X., B. Liu and F. Yuan (2018). Numerical and experimental study of separation control by boundary layer aspiration in a highly-loaded axial compressor cascade. Journal of Applied Fluid Mechanics 11(2), 433-446.##
Mao, X., Z. Yang, B. Liu, B. Zhang and H. Wang (2022). Effects of inlet boundary layer on aerodynamic performance of tandem cascade. Journal of Propulsion Technology. doi:10.13675/j.cnki.tjjs.210738. [Chinese].##
McGlumphy, J. (2008). Numerical investigation of subsonic axial-flow tandem airfoils for a core compressor rotor. Ph.D. thesis, Virginia Polytechnic Institute.##
McGlumphy, J., W. F. Ng, S. R. Wellborn and S. Kempf (2009). Numerical investigation of tandem airfoils for subsonic axial-flow compressor blades. Journal of Turbomachinery, 131, 021018.##
McGlumphy, J., W. F. Ng, S. R. Wellborn and S. Kempf (2010). 3D numerical investigation of tandem airfoils for a core compressor rotor. Journal of Turbomachinery 132, 031009.##
Meyer, R., D. W. Bechert and W. Hage (2003, March). Secondary flow control oncompressor blades to improve the performance of axial turbomachines. In Proceedings 5th European Conference on Turbomachinery, Prag, Tschechische Republik. ##
Roy, B., A. Mulmule and S. Puranam (2009). Aerodynamic design of a part-span tandem bladed rotor for low speed axial compressor. 27th AIAA Applied Aerodynamics Conference 3964.##
Schlaps, R. C., S. Shahpar and V. Gümmer (2014, June). Automatic three-dimensional optimisation of a modern tandem compressor vane. Turbo Expo: Power for Land, Sea, and Air, GT2014-26762.##
Song, Z., B. Liu and H. Cheng (2019). Adaptive particle swarm optimization with population diversity control and its application in tandem blade optimization. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science 233(6), 1859-1875.##
Tesch, A., M. Lange, K. Vogeler, J. Ortmanns, E. Johann and V. Gümmer (2014, June). An experimental investigation of a tandem stator flow characteristic in a low speed axial research compressor. Turbo Expo: Power for Land, Sea, and Air, GT2014-26104.##
Wagner, J. H., R. P. Dring and H. D. Joslyn (1985a). Inlet boundary layer effects in an axial compressor rotor: part I—blade-to-blade effects. Journal of Engineering for Gas Turbines and Power 107(2), 374-380.##
Wagner, J. H., R. P. Dring and H. D. Joslyn (1985b). Inlet boundary layer effects in an axial compressor rotor: part II—throughflow effects. Journal of Engineering for Gas Turbines and Power 107(2), 381-386.##
Wang, H., B. Liu and B. Zhang (2020). Passive control with blade-end slots and whole-span slot in a large camber compressor cascade. Journal of Applied Fluid Mechanics 14(3), 703-714.##
Wennerstrom, A. J. (1990). Highly loaded axial flow compressors: history and current developments. Journal of Turbomachinery 112(4), 567-578.##
Zhang, L., S. Wang and W. Zhu (2019). Application of endwall contouring in a high-subsonic tandem cascade with endwall boundary layer suction. Aerospace Science and Technology 84, 245-256.##
Journal of Applied Fluid Mechanics
Volume 15, Issue 6 - Serial Number 67
November and December 2022
Pages 1745-1758

Files

History

  • Received: 25 March 2022
  • Revised: 21 June 2022
  • Accepted: 08 July 2022
  • Available online: 07 September 2022

Share

How to cite

Statistics